Instructions on how to propagate lavender from cuttings. Works for both English and French lavender and cuttings from new or semi-hard wood.
Lavender can be successfully propagated in various ways depending on the time of year. In summer and autumn you can take semi-ripe cuttings and winter is the time to plant ripe cuttings. But in the spring you propagate by take either soft-wood cuttings, layering an existing shrub or by sowing seeds.
Taking cuttings is basically snipping a piece of an existing plant and letting it grow its own roots. The small plants that result are clones of the parent plant and will produce the exact same foliage and flowers.
Many plants can be propagated this way and it’s the cheapest and most effective way to increase lavender plants. It’s also a wonderful way to share plants in the community! Take cuttings from plants in a friend’s garden and you’ll have plenty for yourself and to give back to them.
It’s a non-obtrusive method of propagation and the parent plant will not be affected at all so the next time you see a lovely rose bush, Hydrangea or Lavender shrub do keep it in mind for a propagating experiment of your own.
Soft-wood is the new fresh growth that plants put on in spring. Each sprig of soft-wood can either be left on the shrub to increase its own size or it can be taken off and used to root a brand new plant. Early on in the spring some of the new green growth might be a bit short but it’s also possible to root from the older wood that the new leaves are growing from. This older stem is called ripe wood and will readily grow roots providing that you cut it in the right place and apply a Rooting Hormone.
Step 1: Taking Cuttings
Cut a section of branch from your plant. Starting from the top, use a very sharp knife cut 2.5″ long sections just below a leaf node. A leaf node is any place along the stem where the joints of leaves grow out of and you can see what this means in the above photo. Using scissors is not a good idea for this step either, in case you had it in mind. They actually pinch the stem as they cut and partially close the stem making rooting difficult. Please also keep track of which end was the top end and which was the bottom. You need to plant the pieces into the soil in the same direction the plant was growing. If it’s planted upside down, the cutting won’t take.
Step 2: Trim the leaves
Using that same knife trim all but the top bunch of leaves from the stem. You need a few leaves to feed the plant but too many forces the plant to direct energy and food to the leaves rather than to the business of putting down roots.
Step 3: Rooting Hormone
Now dip the bottom 3 cm (3/4 inch) of the stem into your Rooting Hormone and then bury the cutting all the way up to the leaves along the edge of a small pot filled with free-draining compost such as 50% ordinary compost mixed with 50% Perlite. Terracotta pots are a bit better than plastic pots for this exercise since Terracotta can breathe, whereas air and water can’t pass through plastic. This breathe-ability creates better conditions for rooting and can also reduce the chance of fungal attacks. And if you’re able to soak the terracotta pots in water overnight, all the better. The ceramic will actually absorb some of the water making the material immediately more breathable.
Step 4: Rooting
After your cuttings have been prepared and planted in the compost water them thoroughly but gently. Place them in a warm place such as a greenhouse, window sill, or conservatory and place a plastic bag over the top. The bag helps to retain warmth and moisture and is essential unless you’re using a dedicated propagator set-up. Rooting will take place within the next month to six weeks. Afterwards, they can be gently taken out, and potted up individually.
Step 5: Planting your new lavender
Once they are about 8-10 cm (3-4 inches) tall you can plant them out in the garden. If you have acidic clay soil, try digging in some Garden Lime and grit a few weeks before planting out. Boggy and acidic soil will cause the demise of your carefully propagated lavender seedlings.
Plastic bags works like mini greenhouse
Growing Lavender from Seed
Like last year I’m also growing Lavender from seed, though it takes quite a bit longer to have adult plants than if you grow from cuttings.
The seeds I sowed two weeks ago are already coming up in their seed tray and I’ve included a picture of them below. They’ll likely stay in their seed tray a bit longer than most of my plants but by summer I’ll have them planted up in large modules before potting them up in individual pots by autumn. The lavender you see growing in the bottom picture comes from seeds that I sowed this time last year and have been overwintering in my cold frame. They’ll be planted out in a newly dug bed in the next week.
Propagating your own plants from cuttings rather than seeds can be a rewarding experience. It’s very easy to do and once you’ve propagated one plant you’ll know how to propagate others. Patience is always key when it comes to nurturing any living thing. Those weeks of waiting for your plants to grow will pay out dividends in the garden.